admin | 
07 31st, 2009| 
FANS
All kinds of materials were used to make the hand fans so popular with our grandmothers, and many of them are very pretty things, well worth repairing.
Fans were made of ostrich feathers set in ivory or ebony; or of bone, ivory, or ebony, or of paper and silk, mother of pearl, or lace. Sonic fans have a ribbon tie running through the sticks which controls the spread, and this ribbon may be torn or very dirty. It is simple to replace the ribbon, but it will probably be threaded in such a way that the fan may be opened and shut easily without pulling or looping. Take a careful note, when removing the old ribbon, of the way the threading is done so that you can put it together properly To clean fans made of ivory, bone, tortoiseshell, ebony etc. treat as described under Ivory and Tortoiseshell.
Broken sticks present a problem if they are made of these materials, and very careful sticking with epoxy resin is the best way if you have all the pieces. A strengthening piece may be added, either of matching material if available or of clear plastic. Replace broken wooden sticks by making a careful copy. Remove the D-shaped ring at the bottom which holds the sticks together if a whole new stick is to be inserted. The straight part of the 1) is a pin through the sticks, and this will have to be taken out (see Fig. 16). If it is riveted through, file back the sides of the rivet at one end until the pin slips out. Put die new stick in its correct place. The pin should be hammered a little to lengthen it so that it can be riveted over when replaced.
Clean fans made of fabric by brushing with Fuller’s Earth. Immersion in any kind of liquid is usually inadvisable because there will be glue about which can all too easily be loosened. Painted colours on fans may not be fast and will run, or be lifted, so take care. Remove spots carefully with dry cleaning fluids such as carbon tetrachloride, or blot out grease spots as described in the section on Needlework, remembering once again that heat will melt any glue.
Mend torn paper fans as described in the section on Books, or put in whole new pieces of paper as detailed in the section on Prints and Watercolours, and revarnish with Winsor & Newton’s Water Colour Varnish if necessary. Sometimes a heavier varnish will have to be used, and Picture Mastic Varnish or Copal will match this.
Generally speaking, fans are delicate objects which need a lot of care and delicate work, as each one must be treated on its merits according to the material from which it is made.
Let the repaired piece cool down completely and then soak it in water to remove the gummed strips. There will be some spots of adhesive along the join squeezed out when the jour was made and deliberately not wiped away. Rub the spots very carefully with glass paper and break them down before removing them with a scalpel or a razor blade. This cleaning is quite a delicate operation and if done without abrasion may result in lifting little chips of china or
glaze.
If the crack was also c’., Red and Aralditc with colouring was used, tidy the filled chips with fine glass paper, and over-paint or glaze if necessary.
Moulding aped Modelling whole pieces of a pot or a
figure are missing, the gap can be filled by rebuilding the piece with epoxy resin composition filler. But it isn’t quite so simple as that! Perfectly satisfactory pieces for plates, vases, bowls, statuettes etc. can be moulded or modelled and simply stuck into place provided the piece is not going into domestic use, but such mends are not strong
g enough
to withstand hard wear for very long unless they are sup- ported by metal cores or pins. It is easy to mould or model a jug handle without a core, but unlikely that it will last very long if the jug is used. If the new handle has a core it will be very strong indeed. The making of cores and pins is described in a later section, and here I shall talk about moulding and modelling without supports. The techniques involved are almost identical when supports are incorporated. The job requires only a few cheap tools until the moment when you get involved in metal work and drilling for supports. And many people, once they reach this stage, just take the work to an expert restorer rather than buy drills and bits etc.
Before mending a piece such as a bowl or plate or vase, without using a core, scratch or file the broken edges so that the new piece of moulding will lock into the edge as it sets. The danger is that your new pieces may not adhere too well to the smooth and thin edge of a break without some kind of roughness in which to get a grip, as the problems of adhesion are not quite the same as those of sticking two edges, of porcelain or pottery together.
Next, a backing is necessary. This means a surface up against which you can press the filler to remake the piece. If the object is a flat plate, with : flat surface, the same gummed strip as is used for binding can just be stuck on the outside surface of the piece completely covering the broken area. As it dries it stretches tight and makes a good smooth surface up against which to press the filler. This gummed paper cannot be used on a curved surface because it pulls taut and flat across the curve as it dries. Therefore the mould will
wihave to be made with a flexible material which will take a curve. Plasticine does the job well, but it never sets hard and can be pushed out of shape rather easily. Wedge plasticine before use—this is a potter’s term meaning quite simply banging it until it has no air bubbles in it. A mallet or a wooden rolling pin make good bashers for plasticine.
If you use plasticine for the mould and Araldite for the filler you will have to get some cellulose acetate to use as a parting agent as the two react upon each other and must be separated by coating the surface of the plasticine which will come into contact with die filler.
There are other moulding materials. The dental impression compound Paribar is more expensive, but is quite excellent for the work, and is worth the extra money for it can be used again and again, needs no parting agent, and has other uses. Paribar is softened in hot water before use and resets fairly hard but is flexible enough to be extricated from quite deeply cut castings.
Making Moulds. Imagine that you have to replace a curved piece with a fluted surface, from the edge of a bowl. The whole of the edge of the bowl is fluted in the same way so you take an impression of a matching piece of the pattern oil a sound section of the edge. ‘Wet the surface of the bowl and press a slab of plasticine (about half an inch thick) on to a section just a little larger than the missing piece. Carry the plasticine up over the rim of the bowl so that it will be marked but don’t bend it too far round the rim if there is any ridge or it may be difficult to remove the plasticine without bending it. Press the plasticine well and truly until you are satisfied that you have made a perfect impression. Lift it carefully off and place it over the hole on the outside of the bowl in exactly the right place so that the pattern is continuous. Press it lightly so that the broken edges of the china mark the plasticine, then remove the plasticise, and paint the area inside the edge marks with cellulose acetate parting agent, then replace it over the hole. It will stick to the dry china round the edges of the break. Bend over the top sections of plasticine away from the hole, round the rim of the bowl to keep die mould in place. A few strips of Sellotape across it and on to the china will help. Don’t use gummed strip, for this will dry out and flatten the mould. The Scllotapc may give slightly but will help to avoid the disaster of the mould coming off the pot in the middle of die filling operation which follows.
Paribar can be used in exactly the same way to make a mould especially where there is a deeply indented pattern in the china. The Paribar goes hard, but it can be softened with swabs of boiling water and removed from die filler section without breaking it when the job is done. No parting agent is needed so that the Paribar can be put directly on to the break and left there.
Filler Composition and Filling. Now to mix up sonic filler (see Fillers and Cements). Araldite two-tube epoxy resin is first mixed together and then titanium dioxide (or other whitener) is added until the mixture has a nice doughy consistency. This mixture is a bit sticky and clings to tools and fingers. Keep a little dish of the powder handy, and another dish of Methylated spirits. Dip your fingers in the powder, and the tools in the Meths from time to time, and you won’t get so stuck up. When dried out this filler looks exactly like biscuit, or unglazed baked china and takes overpainting very well. It also sticks directly to the edges of the break and you should have no trouble in making a perfect join. It isn’t the easiest of jobs to make and handle this filler, but the result is so good that it is worth practicing to get the mixture of the right colour and consistency.
Kaolin mixed with Araldite in the same way makes a very stiff, not quite so sticky, more translucent and buff coloured filler, but it has the disadvantage of not sticking quite so well to the edges of broken china as does the first mixture.
Isopon polyester resin filler is a paste which is mixed with a hardener. It is excellent for filling big holes as it dries quickly, but this means also that you must be able to work quickly. When using Isopon make all inside mould of the break as well, and having filled the mould, put the second inside mould oil to the filler from the inside to get a smooth interior surface, pressing it down well. Isopon requires no parting agents. Although it will stick to itself so that it call be built up in layers, it will not stick to china, so when the moulds arc removed, the new Isopon piece will come away and will have to be stuck in just like an ordinary broken piece. It can be rubbed and filed to finish it off It cannot be used as an adhesive.
Bondapaste is another excellent filler which hardens quickly and does not have to be baked, nor does it require powder additions to make it opaque. It does not dry white, but this is immaterial if you are going to overpaint it any-way. It can be used as an adhesive or cement and when used as a filler it stays in place without further adhesives. It can be filed, carved and abraded within a quarter of an hour of use, so is a very time-saving material, once one is experienced enough to shape it quickly.
The exact consistency of any filler is difficult to describe and can only be discovered by trial and error. If it is too hard it will push the plasticise out of place as you press it into the mould. If it is too runny it will tend to run into the lower part of the mould in whichever place you are holding it, and will not make a piece of even thickness. If the mould is made of Paribar then a stiffer nix of filler can be used.
The mixture is worked into the aperture with a round ended tool. Boxwood potter’s modelling tools are excellent but many things make good modelling tools. Some workers like to prop the pot up as they work, others hold the pot in one hand so that the break with its mould is cupped and held in position while the filler is worked in. Great care must be taken to make sure that the filler goes into all the corners and crevices right up to the edges, with no air bubbles trapped underneath. Smooth the inside surface with the tool and with thumbs and fingers until it is as like the surrounding inside surface as your eye can judge. Setthe pot aside for an hour, if the filler is Araldite, by which time it will have set to a rubbery consistency and can be worked further if necessary. If a quicker setting filler has been used, once it has set hard it can be carved, filed and abraded until it is absolutely perfect, and it is then ready for overpainting.
To speed up the setting of a mend done with Araldite, bake the pot for half an hour at zoo deg. F. If there are any small cracks or pits in the surface fill them with a thin mixture of filler, using a water-colour brush.
Chips. The mending of chips, big and small, which do not go right through a piece, involves work which is halfway between the filling of apertures as described above, and modelling
which is described in the next section.
Quite simply, you make up a mixture of any of the above mentioned fillers into a fairly stiff mixture and press it into the previously cleaned and dried area of the chip and smooth it until it looks right. Don’t get air bubbles under the filling. Wheel chips—large chips on the edge of a piece—should first have a thin layer of adhesive, to help bind the filler in place. The art of filling chips is to get a good blend along the edges and to get the filling neither too proud nor too shallow, and in getting the composition in so that no air bubbles remain behind to raise it in due course. If you suspect that a little air is trapped, prick the filler with a pin and press it down again and fill tip the pin hole.
Allow the filler to dry out over a hot radiator and then, when it is hard, rub it down with glass paper until you are satisfied that the chip, after overpainting, will be indistinguishable. Pick up the piece and squint at it at eye level in all possible planes, and rely on the sensitive tips of your fingers run across the mend to detect any irregularities. If even at this late stage the chip is not properly filled, more composition can be added for it will stick to itself, and the process repeated until you are satisfied.
Modelling. When neither straightforward sticking, nor press moulding can be used to mend an object, try modelling. It is impossible to make a mould for a missing piece which is not a repetition of another part of the object, as described previously. The missing piece just has to be built up from scratch and the result depends on the artistic ability of the restorer. Large modelled sections will have to have metal supports—dowels, or pins, or strips—and the techniques will be described later on. I am still concerned with the techniques which do not include drilling.
When a part of a plate, or a vase, or perhaps a lid knob must be remodelled, take a piece of rather doughy filler composition and roll it either flat for a flat section, or into a ball for a knob, or into a sausage for a handle, in an approximate size and shape for the job. Then press it firmly to the edge of the broken part, and model it with Boxwood tools, fingers and any suitable home made tools that you may fancy. Whenever epoxy resin mixtures are being used, dip the tools in methylated spirit to avoid sticking.
Modelling becomes really interesting when a porcelain object such as a figure or perhaps a vase festooned with flowers and leaves has pieces chipped out or broken off and lost. To remake flowers and leaves is not at all difficult. Any woman who has ever made an apple pie with a decorated crust knows the technique. The pastry, in this case filler composition in a nice doughy mixture, is rolled out to the thickness of the petal or leaf required and then pieces are cut out of it in the flat. A small sharp knife or scalpel can be used as a cutter, shapes having been first marked out with a darning needle or a fine graver. Or, if the leaf or petal pattern is to be repetitive, a cutter can be made out of strip brass or copper foil, beret to make the appropriate shapes. Make a template or pattern out of plywood, using a fretsaw (see Fig. 8). Tack this pattern to your work bench with a central nail and then hammer a copper foil strip round it with a small hammer until it is exactly the same shape. If the template is pinned with a central nail it can be pivoted round as the cutter is being made so that all pieces can be reached.
The cutting of different species of flowers, daisies, roses, apple blossom etc. is hard to describe exactly. It is a matter of careful observation of thepetals which are to be matched, and of measurements with calipers and dividers, if your eye is not good enough. Petals are cut out in flat shapes and bent over slightly at the edges, and rolled into concave shapes etc. Once your petals and leaves arc made they are then fixed to each other and to the main piece, and there is no great difficulty about this unless the anchorage point is very small indeed, especially if you arc using a good adhesive filler composition such as Araldite and titanium dioxide. it is often possible to add an extra leaf, or to put in
small
a smasupport of composition disguised in some way as part of the decoration, which will hold the modelled part in place. Most people have a collection of tools for modelling which they have made specially to get into different corners ; sewing needles, bent knitting needles, scalpels, spatulas, rifflers, spikes and blades of all kinds, even old hacksaw blades, conic in usefid.
When pieces of an object are missing for which no pressed mould can be made, it is still possible to make a mould out of plasticise which approximates pretty closely the missing piece, and to put this on to the whole in such a way that the aperture can be filled with composition in exactly the same way as a pressed mould is filled. Then the new piece must be rubbed and shaped to final perfection after the setting or baking process has been completed; but
this can be a slow job.
There are problems when it comes to modelling difficult things like faces; it rather depends upon how clever you are, but there is yet one more way, which involves modelling. It is a much more complex and tricky job, but it can save such a lot of time and trouble in the long run, -aid once again may enable you to get away with it without resorting to pinning and dowelling.
Make a model, in plasticine, of the missing part. Actually this is easy if you have a talent for modelling, terribly difficult if you haven’t. Say for instance that half a leg and a foot are missing from a figurine. Using calipers and dividers, measure the other leg and foot exactly, so that at any rate lie won’t have a size six left boot and a size ten right boot. Then model a plasticine leg to the right diniensions and in the kind of position in which it looks as if it ought to be, and keep trying your model in the space until it satisfies you. Plasticine doesn’t harden so take as long as you like over making the model.
Having made your plasticine model, a mould must be made from it and a cast or pressing taken from the mould. The finished cast can simply be stuck into position (or dowelled or pinned if necessary).
Take a sheet of glass, and a large lump of plasticise. Roll the plasticise out into a very thick strip and lay it on edge on the glass (see Fig. 9) in a square or a circle plenty big enough to hold the model, horizontally. Then fix the model, horizontally, halfway up one side of the container that you have just made. A peg carefully inserted into the end of the model and pushed out through the container side should hold it into position. Then prepare some plaster of Paris. Into another container which can be handled easily and has a pouring lip, put enough water to half fill the mould container, and sift plaster of Paris powder into it until the mixture is the consistency of thick cream, stirring with the hand to break up lumps. Then pour the plaster of Paris mixture into the mould until it is halfway up the model. Leave the whole thing to set. Then cut two wide grooves or shallow holes out of the plaster.
sure that it is really well drenched and that no tiny part has escaped swabbing. This acts as a parting agent between the two halves of the plaster mould. Make another mix of plaster as before and pour this nito the mould until the model is well covered. When this has set, remove the plasticine case and case the two sections of the casting apart. Take out the original plasticine model and you should have a perfect mould in two halves. This mould will have two locking pieces where you cut the grooves or shallow holes so that when the two halves are put together again they will locate exactly, and at the end where the model was attached to the side wall of the plasticine container, there will be a hole.
Now you have a mould which can be used to make a casting or pressing of your original model. Smear a film of silicone grease all over the pattern sections of the mould to prevent the filler sticking to the plaster of Paris, and then make up enough filler composition to fill the two halves of the mould. This filler should be soft enough to flow freely into the mould sections. When the two sections are filled, bring them together and bind them tightly with wire. Ram the composition well home, through the hole. Leave the mould, with the hole at the top, for two hours to set, and then, if you are using epoxy resin, bake it for half an hour at 2oo deg F.
Undo the wire binding and take off the plaster. If you have not used a parting agent, the plaster can be cut out and broken away and the last of it scrubbed off the model. Stick or dowel the finished model to the whole, having
made sure that the edges fit perfectly by filing and abrading. bradin,
Any discrepancy in fit which is too big to be put right by filing, can be filled with some filler composition.
Moulds can also be made from pieces of porcelain similar to the piece you are trying to replace, and then pressings made from these can be carved, filed, abraded, and built up to fit exactly.
Instead of plaster of Paris, rubberised solution such as Qualitex can be poured around your model. The advantage of using this material is that the mould is flexible and will come off difficult undercut models without damaging them. Rubberised solutions, therefore, are best for making moulds from models which must not be damaged in any way. The technique is much the same as that described above. A plasticine container is built up round half the part to be copied, and the solution is poured in.
The process is repeated on the other half and you then have the complete mould in two sections. Details vary with each job.
Faces on statuettes are very alike, and differ only iun detail of hair and headdress. There is no reason why, if you collect figures, you should not make a series of moulds or masks from any statuettes that come your way, and so build up a stock of faces iii reserve for the day when they may be needed.
Incidentally, the principles of making casts, moulds, pressings etc. are generally similar for work in all kinds of materials, and many restorers of objects other than china, such as old guns and pistols, make their own metal castings. It is a skill which has so many applications, not only for restoration but for creation. Modem materials make exciting castings and pressings, and it is an art well worth studying for its own sake.
ARMS AND ARMOUR
Guns and Pistols
Old firearms arc popular collector’s items, and no olde oake beame type of pub or cafe worth its salt feels fully decorated without weapons on its walls, so good ones are expensive; nevertheless one sometimes comes across old guns and pistols in junk shops and these can be in pretty bad condition. It is usually possible to mend and clean these things and make them look very decorative; by spending money they can be restored to near perfection, and you can even fire them if you dare. For really careful restoration, try to find a picture of a gun like yours or a similar actual weapon in a museum, which you can copy.
As a first step make sure that any gun you buy is not loaded. It is not ridiculous to suggest that an old pistol which has been knocking about for years could be loaded, for it has happened, and even ancient gunpowder will explode violently. Gently insert a wooden rod or dowel into the muzzle and when it will go no further make a pencil mark. Withdraw the rod and lay it alongside the barrel with the pencil mark by the muzzle and the point at which the barrel is blocked can be exactly gauged. The powder must be carefully removed. If you have a shotgun
hi
the cleaning rod wch goes with will it wiprobably have a cap on the end which unscrews to reveal a screw tip. Screw this gently into the charge in the old gun and remove it like a cork. Failing a cleaning rod, an ordinary screw welded to a piece of stiff wire would do just as well. After this the barrel should be washed out with warm water and thoroughly dried.
Unless the gun is really terribly rusted, or contrariwise is in excellent condition, it is probably best to strip it down into its component parts, just as one would when cleaning a modern gun. Normally the lock is removed first by unscrewing it from the stock. First remove the screw which holds the cock (in the flintlock) or hammer (in the percussion lock) and slide off the part. Next unscrew the pivot of the pan cover and the pan cover spring screw and remove tile parts. ‘then unscrew the holding bolts or screws until the lock plates can be removed. (See Fig. i.)
Penetrating oil applied to the screws and left for a while will allow many a stubborn screw to be removed. Do use well-fitting screwdrivers, as if you spoil a screw ]lead by using a wrongly fitting screwdriver it may be impossible to get it out without drilling. The drilling out of screws is extremely tricky and may result in damage to the pistol, so don’t try it unless you must. Expert help may be necessary. One way to loosen obstinate screws is first to place a little lubricating oil round tile head of the screw, and then to touch the head of tine screw for a second or two with the tip of a red-hot poker. This meat causes expansion and contraction to loosen the screw and the oil will penetrate and help with the withdrawal.
Dispiiawlitt,9 a flitalock, arid reassembling (see Fig. r). In order to take the lock to pieces for cleaning or repair the four screws which hold the mainspring, the sear, the scar spring and the bridle, must be half loosened. Then take out the mainspring screw and remove the mainspring. There is a pill at the rear end of the mainspring which engages in the lock plate, and the other end of the mainspring which engages in the toe of the tumbler. Compress the mainspring and it will come away easily. A hand vice is a useful tool for this job. Once tile mainspring is off, the other screws may be removed and die other parts will come off quite easily. Having cleaned all parts with fine files and emery paper or powder, and got rid of all the rust, oil everything well, and cover with Vaseline. Then set about reassembling. lock plate to take the cock on the outside. The scar and the sear spring come next and then the bridle. The square lug on the scar spring fits a slot in the lock plate and holds the spring in position. Compress the mainspring and put it on the lock plate with the holding pin in position, and put the lower end of the spring back over the tumbler toe. Then secure the screw. Without a hand vice, depress the tumbler to the fired position so that the end of the mainspring will go over it. Then put the cock oil and pull it back to the half cocked position so that the tumbler toe comes and compresses the mainspring. The rest of the pieces are put back in the reverse order to removal, the pan cover spring and pan cover going on last.
The barrel of the gun comes off next. This has a metal extension called a tang which runs into the stock. The tang screws are removed, and any retaining bands or pins. Trigger guard, butt cap and ramrod pipes are usually screwed or pinned in place and must be removed with care. If a gun is in bad condition it is likely that the rusty screws and pins are stuck into the wooden stock parts, and too much beef will merely result in breaking off chunks of wood complete with the pins and screws. Gentle tapping and the judicious use of penetrating oil will help. But leave things where they are rather than risk breaking the stock. Expert gunsmiths make their own castings and spare parts, but for those without the necessary tools or ability, castings can be bought, which only need filing to fit. Normans of Framlingham in Suffolk specialise in these parts and have a comprehensive catalogue.
Guns will be more or less rusty, either with ordinary brown rust or that black rust which seems to have eaten right into the metal and looks like black ink stains. When restoring or cleaning any kind of metal, the rule is not to overdo things. Gentle abrasives, gentle cleaners and gentle fingers give the best results. Patience is better than a power tool. Start by applying a mixture of oil and paraffin, or by soaking the metal parts in it. Patent rust removers arc fine if used with care. They should never be left on for a very long time, or they will etch the metal, and will probably dull it, although in this case can always be re- polished. Penetrating oil contains rust remover, so if you have been using this to remove screws, be sure to wipe it all off the metal before leaving the work for any length of time. Clean the inside of the barrel with a wire brush on a rod.
Coll revolver
Draht
ger prawim lock,
Having cleaned off all possible rust, polish die metal work with jeweller’s emery, which is considerably finer than ordinary emery paper and comes in various grades (see Abrasives). Start with a coarse grade and finish with fine grades and you can get a mirror finish. Don’t be too quick to resort to buffing wheels or harsh abrasives; you may make deep scratches or rub off marks or chasings which cannot be replaced. Barrels may have a brown colour which is due to deliberate rusting, so that the barrel would not rust further while the gun was in use. To re-brown a barrel it must first be polished mirror bright and then treated with many successive solutions of a certain acid formula. Gunsmiths guard these formulae closely, and most send their barrels to an acknowledged expert to have the job done. It costs several pounds and would probably not be worth your while, simply to restore a not very valuable piece of junk.
Blue barrels were originally coloured by a heat process. Blueing is equally an expert’s job which takes time and experience, although solutions can be bought which enable the amateur to blue barrels quite effectively.
Clean brass parts, trigger guards, ramrod pipes, butt caps, etc. with ordinary metal polish. If these are missing new ones can be bought (see above) and fitted by filing.
Having achieved the polish and colour you want, the next thing is to maintain it. Be very careful not to handle the metal parts of your gun. after its final polish, as sweaty
fingers leave a deposit which causes spots of rust. (This
applies to ametal work.) A piece of wood carefully
jammed in the muzzle will make a temporary handle while applying a final finish to the gun. Wipe over the metal parts with a very thin layer of oil; or if you don’t like this, try wiping with aduster which is impregnated with silicone—these can be bought for dusting furniture in any hardware store. Some people like to lacquer things on the principle that lacquering reduces cleaning to ‘iaminimum.Un- less lacquer is of extremely good quality, it will darken in time and altogether spoil the look of the job. (See Lacquer.)
The wooden stocks or butts are another matter, and often need a lot of repair. The stock may be completely split. Modern impact adhesives, such as Evo-stik, make a strong join very easy, but it is best to make sure that they do fit accurately, as with impact adhesives once the two faces of a
join are put together they must remain if a good join is to be made. If the stock is chipped or if there is a piece missing, you are going to have to find a piece of more or less matching wood to replace it. Clean the old stock first with fine steel wool and linseed oil. Rub away until the dirt and any old varnish has gone, then you will be able to see the graiui and colour of the wood. Finding the right piece of wood may be difficult. A friendly furniture restorer is about the most likely mail to help—you will only need a small piece anyway. Whittle the new wood to fit with a sharp knife and fine sandpaper. If you are an expert wood- carver and have die tools, making a matching piece should be no problem. Remember, having bonded new and old, that it may be necessary to bore small holes for the pins or screws to take the metal parts when the pistol is reassembled and this should be done with care. When the bond is set, rub the whole stock well with linseed before reassembling the gun.
Shallow dents in wooden gun stocks can sometimes be reduced by steaming. Soak a piece of thick cloth in hot water and put it over the dent and then hold a hot iron on the cloth and get up a good head of steam; this swells the wood and reduces the dents a little, but as the wood dries right out they will probably reappear to some degree.
Gunstocks arc often attacked by woodworm and if this has happened, treat the stock with all anti-woodworm dressing such as Rentokil. If the stock is badly honey- combed, inject syntheticresin into the holes with a hypodermic syringe or even soak it in a thin mix to stiffen the whole thing.
Burr walnut (see Woods) is most commonly used for gun stocks and is mainly imported. You would probably have to buy a new stock blank through the trade and shape it to fit, if a whole new stock is required.
Of course if you can get hold of several pistols all more or less alike, you can make up composite restorations using sound parts from each. What you will have at the finish is a fake, not a restoration, but if it is just for decoration, then it doesn’t really matter, and only an expert will be able to tell that it isn’t the genuine article!
The periodical Guns Review contains much interesting information about antique firearms.
Swords
Swords turn up in junk shops in odd lots with old hickory shafted golf clubs, broken walking sticks and elderly umbrellas, and are usually a relic of somebody’s great grandfather’s service in the cavalry. The services still use dress swords and ceremonial swords, and these, being expensive items, get handed on and do not appear in junk shops. Valuable old swords are real collector’s items and you are unlikely to be trying to restore one of these. However, any old sword can look quite fine once it has been cleaned and polished. Knives and daggers and bayonets come into the same category and are perhaps more common in junk shops. Very often the scabbard, particularly if it is an Oriental one, is as attractive as the weapon itself and warrants as much care as the blade.
As with the restoration and cleaning of any kind of metal object, care is needed. Too violent attempts at rust removal may remove interesting marks or engraving or inlay, and half the fun of cleaning up these things is in what may come to light underneath. A sword, like a gun, can be dismantled into its component parts, and if this can be done without breaking the weapon or damaging it, it is far better to take it apart for cleaning. Blades were often made somewhere other than the hilts or sheaths, and the whole assembled by sword-smiths before sale. Parts got broken and were replaced, and a sword or a dagger can be a composite bearing different makers’ marks and still be quite genuine. If you find a sheathed sword in a junk shop, take it carefully out of the sheath holding the whole thing pointed downward. Be especially careful with knives and daggers for an old scabbard can split as you take out the weapon which may still be razor sharp.
To take a sword apart (see Fig. 3) first check the button at the top of the hilt. The tang, or top end of the blade, passes right up through the Ht and the pommel at the top, and is then burred over the button to hold the whole thing together. File off the overlap and slide the blade from the hilt; but it may not come out that easily. Later swords may have a screw-iii button. Grip the blade in a vice, near the top, but make sure the vice is padded, or the sword well wrapped, so that it will not be marked by the vice. Using a piece of hard wood as a punch, tap the base of the pommel upwards away from the grip, working round and round it till it loosens and the hilt begins to slide off the blade; but do be careful not to damage anything. Best leave well alone if there is no movement at all. Penetrating oil may help, if you can get some to run between the tang of the blade and the hilt. If the sword has only a small pommel, tap the hilt round the shells, at the bottom. Once again, be very careful for it is terribly easy to break castings.
Now the blade and the hilt are separate and can be coped with on their merits. If the grip is wooden and covered with leather, it may be split, and you will have to carve yourself a new grip using the old one as a pattern. Beech and walnut are tile most common woods, but any wood could be used to remake a grip which is to be covered—after all the sword is not going to be used in battle. If the grip is leather-covered, and the leather is sound, give it a good dose of leather dressing. There are various proprietary dressings and the same one can be used on a leather sheath. Some dressings give a long-lasting finish, others need more frequent renewing (see Leather Dressings).
A new leather grip cover can be made quite easily by cutting out a piece from any suitable leather. Clean off all the old leather and make the grip smooth and clean. Then very carefully pare or bevel the edges of the new leather grip so that they fit round the handle without a ridge where the join conics. Soak the leather and put it on the grip, smoothing it to fit. Then bind it on to dry. Rubber bands may leave grooves in the leather, so some kind of wide tape or bandage just to hold it in position while it dries is better. When the leather is quite dry, remove the binding, and, very carefully, the leather piece which should by now be exactly the right shape and fit. Using an adhesive, such as Evo-stik which will not stain the leather, stick it firmly to the wooden grip. Very often lints are wholly or partly bound with brass wire. If this has to be replaced, two strands of brim piano wire or picture wire, twisted together, make a good job. The actual binding is not so easy as the ends of the wire have to be neatly tucked in.
The cleaning of metal hilts andblades must be care- fully done. Brass and silver hilts will probably conic up well with ordinary metal polishes and some elbow grease, but steel hilts will need rubbing with abrasive. Make up various pads and sticks to help with the rubbing down,
well
checking that the stick is wepadded with foam rubber under the emery paper; this makes it easier to get into difficult corners. Blades which have inlay should be treated very gently, as any rough treatment will bring it off. Soap and water and a soft cloth for drying are die best; certainly it is dangerous to use strong metal polishes or rust removing preparations. Clean plain blades and steel hilts with oil and paraffin mixture to remove loose rust, and then wash with strong detergent to get rid of all grease. Clean very greasy metal with carbon tetrachloride. Then wipe rust remover on the metal and remove it after a few minutes. You will get some idea of how much rust is going to shift, and can repeat the treatment until the metal is clean. The big danger is that rust remover, if left too long, will work unevenly and will start to etch the metal, and you will end up with a pitted surface. Oriental swords are very often meant to have a dull finish, and after a wipe over with rust remover, all they will need is a polish with a soft cloth, whereas Western steel is worked over with emery until it has a mirror finish. Don’t get fingerprints on to the polished metal or they will form rust spots in time. Rub the finished metal over with a light film of oil, or use a silicone-impregnated duster or silicone furniture polish, sparingly, on a soft cloth. Lacquer, if used, must be of high quality, or it will darken in time and have to be removed. Lacquer is really a lazy and not wholly satisfactory way of finishing polished metals (see Lacquer).
If metal parts of the hilt, quillons, shell guards etc., are broken or damaged, it may be possible to braze carefully shaped new parts into place, but this does seem to me to be a job for the expert as it requires special tools and a knowledge of technique.
If the top of the tang was filed off to free the blade, hammer out the tang a little so that there is something to burr over again on replacement. Be very careful, and hammer gently with the tang laid flat on a block. Reassemble hilt and blade and tap it into position tapping the pommel well home. Use a small mallet or a piece of wood, not a metal hammer. Burr over the top of the tang with a punch and file it smooth and neat.
If your sword or dagger has a metal scabbard, treat it in the same way as the blade, cleaning with great care if it has any engraving or inlay. If it is plain, wipe it with rust remover and rub with abrasive, and finish it with a silicone wipe.
Damaged leather scabbards take some mending. If the stitching has gone, it may be possible to restitch it, but often the holes have broken out and the leather is dry and dead anyway and won’t hold stitches. Just stick the edges together as neatly as you can with adhesive.
If the scabbard is broken, insert a strip of cardboard or veneer or plastic to support it. If leather is in good condition all it needs is a wipe with ordinary leather dressing. Sonic scabbards have been stained and polished or boned, these are best retouched and polished with ordinary leather polish.
Old pieces of armour, even complete suits picked up iii very bad condition, can be completely cleaned and done up. The methods used for cleaning sword blades, guns etc. arc suitable for armour. Museums use a phosphoric acid cleaner known as Deoxidise.
I know of someone who bought a terribly rusty old suit of armour for C20, without knowing anything about it, and cleaned and restored it and sold it for 0300. I suppose the basic cost of 4zo puts it outside the category of junk, but it is the kind of profit one likes to dream about.
Burnishing. Any cavalry mark will tell you that the only way to get swords, cuirasses, spurs, bits irons etc. chromium bright is to burnish diem. They are first cleaned with metal polish and then burnished. A burnisher is a leather pad with small steel rings like chain mail sewn to it, arid the object to be burnished is rubbed very hard with this pad. The metal will come to chromium brightness if you use enough elbow grease. The object is then greased very lightly, or lacquered to preserve the shine; but before doing this, small objects can be kept dry and bright in a bag of bran.
By the way, the shoulder pieces of a trooper’s dress uniform, which look like pieces of chain mail, are in fact ornamental burnishers.
Bits, irons and spurs are ornamental enough to become collectors’ items, and they should be burnished as described, or by being put into a canvas bag with a handful of ball-bearings and swung around for a bit. It is air old trick to burnish a curb chain by folding it inside a big duster or piece of cloth, and then, holding both ends tightly, to swing it about with a circular motion.
ABRASIVES
In order to remove rust, tarnish or corrosion from metal of all kinds, when soap and water, oil paraffin mixture, rust removers, metal polishes, etc. have failed or are unsuitable, abrasives are used. In order to get a mirror finish on metal the correct use of die right abrasive is essential. To all intents and purposes, as they get finer, abrasives become polishes. Damaged woodwork can be cleaned and tidied with abrasives, stains and blooms on varnish can be removed; and used in conjunction with paints and varnishes, abrasives help to get deep glossy finishes.
As a general rule, work is started with coarse abrasives and finished with fine abrasives.
There are many different kinds of abrasives, and each
user tends to prefer certain ones; it is not necessary to have
aof them in your workshop. Abrasives can be bought in
loose powder form, as cloth or paper, or in bar compositions for use with buffing tools.
For the purposes of this book it should be useful to describe briefly some of the abrasives and abrasive polishes available. In the various sections, abrasives are mentioned constantly iii respect of specific uses. When working with them, trial and error is the best guide, provided that trials are not carried out on such a big scale that the error becomes irrevocable. After a while an invaluable experience of abrasives and their uses will be built up. Abrasives such as sand and glasspaper, either in sheets or discs for power tools, are used for stripping down and smoothing wooden surfaces, and iii conjunction with paint removers or by themselves, to remove stubborn old paint and varnish. When using sheet sandpaper, glass-paper or emery paper, it call be folded round blocks of wood, or made into sticks by wrapping round pieces of dowelling etc. Discs for sanders on power tools are made in a multitude of grades and qualities, some very rough indeed. Spaced grit carbide discs are excellent for tough work, where scoring of underlying wood can be removed at a later date. Metal discs with tungsten spaced grit over them are almost indestructible and will remove practically anything, but are liable to do damage as well, and should be used with great care.
Sheets of sand or glasspaper are used on finishing power sanders which do not revolve, but work with a fast backwards and forwards action.
Wet and dry emery paper in various grades, so called because it can be used dry or soaked in water as a lubricant without dissolving into pulp, will help to impart a mirror finish to any object which is being painted or varnished. The object is rubbed down with wet anddry between coats until the surface feels perfectly smooth to the fingertips. The emery is used very wet and the lubricating effect of the water helps the emery to cut smoothly without scratching.
Steel wool in various grades is a very versatile material. In rough grades, in conjunction with strippers, it will help to shift paint and varnish. Used with metal polishes it will remove stubborn stuns on metals, and will help chemical rust removers to shift rust. Steel wool pads impregnated with soap are excellent for cleaning greasy metal or wood surfaces. Mirror finishes on wood call be rubbed down with fine steel wool, before waxing to achieve smooth shining but not over
glossy finishes. The uses of steel wool iY1 C011-
junction with wood finishing materials are many, and experience is invaluable. Grade oo or 000 is used for fine work. If you have a polishing lathe with interchangeable mops and brushes, or even if you set up a power drill to take small mops and bobs, you may wish to try liquid polishing compositions. These are equivalent to the bar compositions mentioned below and are intended to be sprayed on to the work as polishing is taking place. This requires special spray equipment so this method is usually only used commercially.
Emery powder, tripoli powder, rottenstone (a mineral found in Derbyshire and mixed with oil), jeweller’s rouge (powdered iron oxide), pumice powder (powdered volcanic lava), crocus powder, carboruriduni, and whiting are all abrasives commonly used in metal finishing, and can be bought in composition bars, either greasy or non greasy, for use with polishing mops and brushes. They are used moistened on soft rags, or on swabs made up on sticks, or on small brushes (old toothbrushes come in handy here).
Obviously care must be taken not to use too strong an abrasive for your particular job. Do not risk making deep scratches which will need even deeper abrasion to be removed, and as polishing proceeds, use finer and finer abrasives until a deep glowing finish is achieved.
ACIDS
Some acids make effective cleaners. They should always be handled with care; rubber gloves must be worn, and the bottles or containers must be carefully labelled, well stoppered, and kept out of the way of children. If you do spill acid on to yourself or your clothing, wash with plenty of clean water and then with water and bicarbonate of soda which is an alkali which will neutralise the acid. When diluting acid, alivays add acid to the water and not vice versa.
Hydrochloric acid. Also known as spirits of salt. Don’t let it get near stainless steel or other metals, except under control, for it will etch the metals. Nor should it touch nylon or any man-made fibres.
Acetic acid. Is the acid constituent of vinegar.
Oxalic acid. A poisonous acid which has many uses as a stain remover. In five per cent solution it will remove ink stains. Two teaspoonfuls of crystals in two pints of cold water will remove blood stains. In saturated solution it will remove black water marks on wood.
Citric acid. A ten per cent solution is sometimes used for stain removing.
Nitric acid. This is a strong fuming acid and if you get will
any on your skin it burn severely. Any slightest amount spilt should immediately be flushed and flooded with water. Skin should be held under a running cold tap. Very diluted, it is used for cleaning gilt and gilding. It can be used to darken soft soldering.
Oleic. Acid in an oily base.
Muriatic acid. Another name for hydrochloric acid. Accumulator acid. Diluted sulphuric acid used in the making of chlorine gas for bleaching.
ADHESIVES
The problems of getting one thing to stick to another have always loomed large for the restorer, especially when the two objects are not made of the same material. Luckily, new types of adhesive have been invented which will literally stick anything to anything. The strength of the stuck joints is also very important, and modern adhesives are so efficient that stuck joins can actually be stronger than any other kind of jour, and where, in the old days the glueing of joins of all kinds was used in conjunction with other fixing methods, dowelling etc., sticking alone is nowadays often sufficiently strong. Adhesives have become so strong as well as water and heat resistant, that it is really no longer necessary to rivet ceramics, and almost totally invisible stuck joints can be made in china. Adhesives mixed with colouring matters, pigments and powders, are used as Hers, thus becoming dual purpose materials (see under Cements and Fillers). Most modern adhesives have many uses and will stick a very wide variety of substances, but some are better than others for particular kinds of work.
Why things stick together is quite involved and difficult to explain. Theoretically, if you can bring two stir-faces together so that they touch all over their surfaces, they may stick together without adhesives. Two sheets of glass will sometimes adhere in this way and become extremely difficult to part. Even two sheets of shiny paper will stick together. I know a trick with a penny, which consists of drawing a coin sharply down a varnished wall surface, and snapping it on with a thumb. The coin will stay there indefinitely if the wall surface is all right. I suppose most of the air is expelled from under the coin, and the rim makes a perfect seal with the varnished surface, and die outside air pressure keeps die coin in place. There was a pub in Potter Heighain in Norfolk, called the Falgate, where the whole surface of die bar surround was covered in coins put there in this way. In fact my father put up the first one. Much later they were all varnished in to preserve them, but eventually the bars in die pub were enlarged and down came die panelling and the pennies. Yet few people would believe that no adhesive was used to keep the pennies up and many of the coins were there for years.
It seems that the function of an adhesive is to make the respective surfaces so smooth that they adhere. When using normal adhesives, as little as is consistent with covering the whole surface should be used, as too much just keeps the surfaces apart, and does not john them together. The john should then be put under pressure and left undisturbed.
All surfaces which are to be stuck together must first be thoroughly cleaned of old grease and glue, or rust, and the adliesive makers’ instructions should be followed carefully. Glues made from gelatine or old type animal glues, can be removed by soaking with warm water. Resinous cements are dissolved by alcohol, celluloid cements can be removed with amyl acetate or acetone. Dissolver will shift modern epoxy resin glues. Once the surfaces are cleaned they should have a rub with sand or emery paper, to make sure all glue is gone, and to give a key for the cement.
Scotch glue. Scotch glue has always been the traditional glue to use for woodwork, and it is still the best glue for veneer work especially where the veneer has to be smoothed or `hammered’ into place with the rounded end of a ball-peen hammer. Scotch glue can be bought either in cake, pearl or powder form. The glue is put into a proper glue pot with water, and left to soak overnight, which makes it swell up and soften. The glue pot is in fact two pots, one within the other. The outside one holds water, the inside one the glue, just like a double saucepan. The pot is put on to simmer and the glue stirred frequently as it heats. Don’t ever boil glue, just get it hot enough to run off the brush when you hold it over the pot, without forming tears. Scotch glue is used hot and is brushed well into the surfaces. It helps to warm the wood before applying the glue. All joints made with Scotch glue should be well cramped or weighted, so that any surplus is squeezed out, and the surfaces brought as close together as possible. Scotch glue is useless for joints or mends which will be exposed to damp, as it will not hold, and in time will even grow fungus. Santobrite call be added to Scotch glue to prevent the formation of fungus. Heat also melts Scotch glue and releases joints.
Durofix. Durofix is a celluloid cement, and is extremely useful as it is transparent, so that it can be built up in layers to form a self-supporting film to repair glass etc. (although acrylic resins have supplanted it for large-scale jobs of this kind). Glass repaired with Durofix won’t stand domestic handling, but for ornamental use it is good enough. One big advantage of Durofix is that it is a one tube adhesive and does not have to be mixed with hardeners.
Et,o-stile. Made in several different types, this is a splendid impact adhesive. Evo-stik Impact Household Adhesive is excellent for joins where the two surfaces may be brought directly together and left without movement until set. Where joins have to be slid together (such as a mortice and tenon joint), this adhesive is not suitable. When using Evo-stik, a coat of the stuff is put oil each surface to be joined, and is left for at least a quarter of an hour. The surfaces are then brought together correctly (no sliding about to get things right), and an immediate bond is made which in time is extremely strong. In fact if you try to break the bond, you may break the wood instead.
Cascattdte is a powder glue which is mixed with water, is good for woodwork, as is
Aerolite which is a powder and a liquid hardener, mixed together in the right proportions for a very strong resin adhesive.
This brings me to the modern epoxy resin two-tube adhesives which are fantastically useful and versatile. There are quite a few makes, and it is not possible to list more than one or two of all the adhesives available in this section, but I think I have mentioned enough to cope with most
jobs.
Plastic Padding. This is a two-tube adhesive and filler, which has a silver metallic colour. It has the advantage of drying very quickly—in ten or fifteen minutes—so that it is useful
will
where speed is helpful. It stick pretty well anything to anything, but its silver colour precludes its use where the join will show, or will not be painted over.
Araldite. In the two-tube pack (A.V. too and H.V. 100), Araldite is suitable for joining any of the materials listed below. All objects to be glued should first be cleaned, the surfaces being thoroughly degreased, then abraded, then degreased again before the adhesive is applied. Also it is important to make sure that surfaces are dry before adhesive is applied, so give them a few minutes in front of a fan heater or on a radiator; or put large objects in an airing cupboard for a while. If there is any paint or old glue on a surface to be joined, it must be removed with a solvent. Dissolver will remove Araldite if it has been used before.
Mix your adhesive on a small piece of glass with a palette knife. Keep some methylated spirit handy for cleaning up, as it will dissolve Araldite while it is still soft. It is important that the contents of the tubes never mix except as and when you want them.
When using two-tube Araldite A.V. ioo and H.V. i oo, warm the two tubes a little before measuring out and mixing the adhesive and it will be thinner, and thus easier to use, but may take a little longer to set.
For china repair Araldite A.Y. 103 and Hardener H.Y. 951 are very suitable because the mixture is thinner; it grips very hard and doesn’t need much pressure to get a good join. Because itis thinner it can be got into small cracks, and it fills all the requirements of unobtrusive adhesion. It is not quite so resistant to water and steam as the two-tube Araldite, so should not be used for repairs to china which is going into domestic use.
All adhesives nixed should be used within an hour as it begins to dry after that time and gets tacky. It is sensible to have a sticking session—collecting together and preparing all the mending jobs you have on hand to do at the same time. It is quite difficult to mix the exact small amount you need for one article and only too ofter, the whole family searches the house for things to mend to use up the adhesive. Left over mixed Araldite will keep in the freezing compartment of your refrigerator for several hours, even overnight, but do not try to keep it there indefinitely or you will end up throwing a useless little hard lump into the dustbin together with the container or sheet of glass to Which it has become firmly stuck.
It is quite simple to measure out the two-tube Araldite exactly because you can squeeze an equal length strip from each tube on to the glass. With the thinner types, measurement is by drops, oreven with two hypodermic syringes— although this would seem to be all expensive way of doing the job. Perhaps it is worth the investment if you are specialising in repairing things with Araldite!
Having mixed the adhesive, spread an even thin coat on each surface of the object, using a match or a rust free nail or a glass rod, and fit the two firmly together. Use gum strip to bind together a join while it dries (see section on Chita). Araldite takes twelve hours to set at room temperature, and three days to harden to maximum strength, but drying can be speeded up by heating, even by baking in a cool oven.
Drying time at 149 deg. C. (3oo deg. F.) 3o rains.
121 deg. C. (zso deg. F.) i hour
79 deg. C. (175 deg. F.) 3 hours
Do not dry at over Soo deg. F. as at that heat the two-tube Araldite resin darkens.
To join the following materials (all must be degreased before and after abrasion):
Brass: Abrade with emery
Ceramics and Porcelain: Abrade with carborundum and water slurry Copper: Abrade with emery
Glass: Abrade with carborundum
Gold: Abrade with fine emery or crocus paper
Lead, Tin and Solder: Abrade with fine emery
Leather: Degrease with great care. Abrade with glass paper Silver: Abrade with fine emery
Steel and Iron: Abrade with emery
Stone: Abrade with a wire brush
Wood: Abrade with glasspaper
Pastes. Special pastes such as Gripfix, and photographic mounting pastes are most useful for paper work as they do not cause cockling or staining. Some photographic mountains have first to be painted on with a soft brush, and then, when the paste has dried for some minutes, the picture or paper is ironed on to its mount with a warm iron over greaseproof paper.
Paste for paper and leather similar to paperhanger’s paste, proprietary brands of which can be bought, are made up as follows: Recipe i. lb. plain flour
oz. powdered alum
Mix with water to a cream, and then add a pint of cold water and heat in an enamel saucepan stirring all the time.
When using this paste for leather add a little thin Scotch glue. Keep this paste away from metal before use or it may pick up discolouring stains.
Recipe z. i teaspoonful plain flour z teaspoonfuls cornflour J teaspoonful alum
3 oz. water
Mix all ingredients together well so that there arc no lumps, bring to the boil in an enamel saucepan, stirring all the time, and boil for a minute or two till thick.
Copydex is an extremely useful white, rubber-based adhesive for all fabrics.
H.M.G. This heat and waterproof adhesive is good for some jobs because it is clear and quick drying, but it is not over strong. It can be handled for up to an hour, and goes totally hard in twenty-four hours. It does not slip, and is dissolved by acetone.
AMMONIA
Ammonia is a gaseous compound of nitrogen and hydrogen. It has the property in liquid form of turning grease into a soluble soap and so removing it. Used as a ten per cent solution in water it gets rid of dirt and grease, and some kinds of silver tarnish. It also makes glass and porcelain sparkle. It should never be used on bronze, and can lift varnish on wood. It is in fact, in a strong solution, quite a good varnish stripper (see Stripping).
Scrubbs Cloudy Ammonia is a ten per cent solution.
Ammonia solution is used for cleaning Ormolu (see Ormolu) and in a very dilute form, marble. A few drops added to beeswax and turpentine (see Beeswax) makes effective furniture polish.
ANTLERS
Antlers and horns, mounted on shaped boards—relics of our big-ganic—hunting grandfathers—are quite common junk objects. If it so happens that you do wish to restore such an object, clean the horns as suggested under Ivory and Bone. Fill any holes or chips with epoxy resin suitably coloured with kaolin powder and a little yellow ochre or brown dry powder pigment to match. Stick broken pieces back in place with Araldite, and put a wire core or pin in hollow broken horns, packed round with filler as described in the section on China Mending. The clean horns or antlers should be coated with a light wax polish to improve their looks. The backboard may need mending or completely stripping off, and repolishing.
Antlers which come complete with the deer’s head are more difficult to cope with if the head is in bad condition. A good brushing with Fullers Earth should clean the hair, but the repair of rotted or torn leather sections may be very tricky and take careful needlework. It may be necessary to re-stuff parts of the head. A good mothproofing is always advisable, so spray well with an aerosol niodiproofer, and an insecticide as well, if necessary.
The first revolvers produced by Philip Webley have already been mentioned greak modern firnuture. For some, years he seems to have manufactured revolvers on a modest scale, most of which were sold through dealers, who put their own names on both the weapons and their cases wash stands for center bowl. A number of them achieved the distinction of being purchased as Presentation pieces fiddle shape antique silverware. The following year saw the appearance of the first firearm which was to make the name of Webley so well known rockingham porcelain. This was the so-called R furniture by charles ashbee.I seventeenth century english stoneware.C arc design in drawing room. revolver, which was used to equip not only the Royal Irish Constabulary, after which it was named, but also several Colonial military and police forces, including the Cape Mounted *Rifles collecting clarice cliff. The barrel was short, being only 41 inches, with a calibre which was nominally ‘45o but actually ‘4′12, It had a solid frame, a six-chamber cylinder and took a centre-fire cartridge swan kandler plate. It established a considerable reputation for reliability, and was subsequently made in a number of different patterns and calibres pewter armchairs. It was still in active use in -many, parts of the world at the end of the nineteenth century antique english oak sideboard grape engraved.
A modified version of this revolver of rather lighter build and with a very short barrel of only 22 inches and ‘450 calibre was made in 1883 gueridon tripartite base table. It was adopted by the Metropolitan Police and various other police forces in Great Britain multipurpose dressing table. In Webley x7go—x953 there is the following interesting account of a remarkable feat by Henry Webley using this weapon:
`With this stubby weapon, designed purely as a short-ranged man-stopper, Henry Webley gave a demonstration of shooting that has probably never been surpassed with a similar arm antique china furstenberg. It was reported antique german furniture for sale.in many papers of the day, including The Standard, The Shooting Times, The Birmingham Daily Gazette, and the Birmingham Daily Mail wheat shaped dining table base. The following account is taken from the last paper, dated 21st May, 1884—” art deco furniture germany. antique japanese tea table. antique american tilt top pedestal table. In demonstrating to his police pupils the manner in which the revolver ought to be used, Mr antique game bird dinner plates. Webley fired five shots at nine yards at a target having a bulls eye two inches in diameter british dining table 19th century. The result was that the bullets were lodged in a space 2J in comtoise clocks longcase. by il in french chairs black leather. Then the range was increased to fifteen yards, and five shots were fired at a similar target, the bullets in this case being put into a space 21 in antique dining table with carved x shaped legs. by il in bugatti sideboard. The next move was made to a distance of twenty-five yards from the target, and at this range five shots were fired by Mr table octagon inlaid drawer european austrian. Webley indian interior low seating drawing room. The same undeviating accuracy was maintained, a surface 21 in 19th century louis xv mahogany french chest of draws floral inlaid wood with marble top and glass cabinet with cabriole legs. by 31 in 17th century painted cassone. being eugene gaillard chair. riddled, Having wit-, nessed the expertness of their instructor, the police sergeants had a little practice to themselves, - and soon satisfied Mr antique rotating dumbwaiter. Webley of their ability to make good use of their weapons at long and short ranges napolean empire furniture. The sergeants who took part in the experiments will in turn act as instructors to other members of the force marcel breuer pel. victorian draw leaf table. meissen dot period. papier mache tray-c19th.”‘
A very similar revolver with the same short barrel had been introduced in 1878 antique thonet wien 3 legged chair. It had a short rounded butt and was made in two calibres: ‘450 and -422 nabeshima antiques. This little weapon was very popular and was known everywhere as the ‘British Bulldog’ construction of antique teaspoons.
The success of the firm was established by the purchase, in 1877 of the patent taken out in November 1876 by Charles Pryse (of C american made ceramic french figurine. & J borghese lamps. Pryse & Co antique scandinavian raised panel flower painted & mirrors cabinet.) for a ‘break-open’ revolver with a barrel latch and a self-ejection system dining room sideboards that look gaudy. This, as shown in the quotation from Mr sheffield plate candelabra. Scurfield, was an extremely popular weapon wooden upholstered arm chair. It had a double-action lock and the first models had a calibre of •38 art nouveau, armchair stained wood and glass,1904. Later an Army pattern was produced with a calibre of ‘45 spanish revival sofa. This Webley-Pryse was the, forerunner of Webley’s Army revolvers, and its main features were embodied in the first of them,
In 188o the Webley-Kaufman appeared 19th century french shaving basin. This was a break-open revolver with a double-action, a five-chamber cylinder and a calibre of -45-
In 1882 Webley constructed his first revolver with both a break-open action and a simultaneous self-ejection system sheffield plate candelabra. This was basically the same method of opening and ejecting which has been retained by the firm of Webley ever since early 19th century french bureau. There followed in 18 86 Webley’s Mark I, which was virtually the 1882 revolver with some standardization of parts antique drop front desks. This was submitted to the Government, and after very thorough tests by the Board of Ordnance it was accepted as the official revolver for the Army “art deco dresser” and “marble top”. The calibre was -45 and the length of the barrel four inches art deco wooden chair.
The initial -order for the Army was io,000 revolvers, and a copy of the original letter is reproduced in Webley z7goz953• It reads as follows:
WAR OFFICE, PALL MALL, S what style of furniture is a kidney desk characterized as?.W tilt tea table chinoiserie.
`Gentlemen,
`In reply to your letter of the 25th ult art deco examples., I have to inform you that this Department undertakes to give you an order for io,000 Webley pattern revolvers at 61 — each on your completing a pattern for approval, delivery to be made at such times as may be agreed upon hereafter rectangular mahogany extension table square pedestal base bun feet. It is probable that from 2000 to 3000 could be taken before the 3 Ist March 18 8 8 hand of fatima with arabic writing.
`A formal contract with the necessary clauses shall be concluded directly the pattern is sealed antique new england drop front desk.
`I am, Gentlemen,
`Your obedient Servant, 18th century english crescent marks. painted sideboard pine maryland.
Two years later an improved model, the Mark II, was introduced dutch lion paw dining table. This had a larger hammer and an alteration to the shape of the grip bugatti sideboard. In the same year Webley made a special target model, the W sphinks wall tiles holland.G antique wooden commode with chamber pot. (or Webley-Green) german antique throne chair. It had a calibre of ‘476, and was made with two different barrel lengths, 6 inches and 71 inches 18th and 19th century silversmithing. The front and rear sights were both adjustable potters stoke on trent empire rococo.
A modified W telescoping table.G 1920’s antique mahogany tables. known as the ‘455 476 Army Model was produced in 1892 maggiolini and cabinet maker from the 17th century. It had a flared butt, six-inch barrel and was without the adjustable sights putti on dutch delftware. It was never an official revolver but was very popular with Army officers, and was in treasured use by many of them until -455 pistol ammunition ceased ‘to be an official issue antique blue glass desert. The writer had a gorgeous model, which, with a magnificent disregard for the modern vulgar craze for camouflage and concealment, was completely covered in nickel plate antique talavera for sale. Beautifully balanced and earning its fortunate owner many antique walnut writing table with pillar (post) legs. a bottle of beer on the revolver range, it was reluctantly retired when the ‘38 weapon finally replaced all the official large bore Webleys king george 1v tankard sheffield plate.
A modification of the standard Webley of 1889 was produced to meet the requirements of the Wilkinson Sword Company leg design for small tables. This `Wilkinson-Webley’ had a six-inch ribbed barrel, a modified grip, a bead foresight and a special cam lever antique tray. Most of the Wilkinson modifications were retained as permanent features, and the Mark III Webley of 18 93 was substantially the same as the Wilkinson-Webley, but with a four-inch barrel brass drum tables.
Meanwhile, in 1887 Webleys had taken over the firm of Tipping & Lawden, of Constitution Hill, Birmingham antique victorian wedgewood pottery smaa jug. In 1897 there was a further expansion owing to the amalgamation of Webleys with W jiajing ming porcelain. & C antique ivory and silver tableware. Scott & Son, and Richard Ellis & Son commodore perry corner cabinet. As a result the concern became a Public Company which was registered under the name of the Webley & Scott Revolver and Arms Co istoriato china., Ltd petite french mantel antique clocks.
The french 17th century furniture gentleman’s dresser.firm of W johann carl schoenheit meissen. & C lady’s bureau: henry van de velde. Scott & Son had been founded in Birmingham by William Scott, who set up an establishment in Bath Street in 1834 antique drum shaped table. He was later joined by his two sons, W “chest of drawers” cherry 1840s. M porcelain spanish dancers. Scott and James C queen chamber pot. Scott drop leaf tea table spanish. In due course the business was transferred to a new building in Lancaster Street, Birmingham, entitled the Premier Gun Works czechoslovakian quality porcelain.
The Mark IV Webley was produced just before the Boer war, and was the standard revolver issued to the troops for the campaigns in South Africa antique 17th century dresser. There were two different lengths of barrel: four inches and six inches; and the hammer was smaller than that of its predecessors crockery cabinet design. The Mark IV was manufactured until 1914- It was succeeded by the Mark V, in which the cylinder diameter was increased by -on inch for nitro powder english column candlestick creamware. A few of these revolvers had six-inch barrels, but they were practically all four-inch czechoslovakia antiques. The short-barrelled model of both the Mark IV and the Mark V was used to equip the- mounted troops in the First World War antique glass epergne.
Twenty thousand of the Mark V were ordered, and with the completion of this contract in 191 5, a new weapon for the Army, the Mark VI, was introduced antique mahogany tea table. This, the best known of all etruscan pottery olive. Webley revolvers, became the universal short range weapon spanish cabinets. It had a six-inch barrel (though a few were made with a four-inch one), altered sights and a modified grip bureau plat charles boulle. The contract stipulated a weekly delivery o•,25oo; and, in all, some 300,000 were delivered france antique collectors.
10 1921 Enfield took over the manufacture of the Mark VI, under the official name of the Pistol, Revolver, Webley, Mark VI 16th century florentine italian credenza. In 1700 french fashion pattern book. 19,26 it was renamed the Pistol, Revolver, No collecting antique brass candlesticks. r, Mark VI; though it was still known universally as the Webley revolver for the remainder of its official career crackle glaze jazz figures 1920s.
Already mercury barometer. in 1922 it had been officially decided that a lighter revolver of smaller calibre was required, if one could be produced with equal, or nearly equal, stopping power french neo-rococo marble top table. Webley & Scott Ltd tea table with gated legs. (the name which the Company had adopted in 1906) were requested to carry out’ experiments antique wales footed dessert platter. The result was a -38 calibre revolver which was in all essentials a smaller version of the Mark VI, and modelled in part on the ‘38 police model Webley which had been produced in 1897 charles mackintosh wardrobe. Like the previous Webleys, the new ‘38 had a lead bullet, and the cartridge charge gave it a greater muzzle velocity than had been achieved with any previous cartridge of the same length in this calibre walnut armchair josef urban art noveau. The lead bullet, to comply with the Geneva Convention, was ultimately replaced by one with a nickel cover japanese mother of pearl furniture.
In 1929 russian oak parquetry refectory table. production of the new revolver was put in hand, but it was made at Enfield as the Pistol, Revolver, No bugatti furniture range. 2, Mark I, and differed slightly from the original Webley conception antique book ends. The firm of Webley, in the meantime, went ahead with the manufacture of their baroque table clocks of gilded brass 17th century.own Mark IV ‘38 (the earlier police revolver having been Mark III) inlaid refectory table. Large numbers of these ‘38 Webleys were produced for the Army in the Second World War; and this explains the appearance of two apparently similar weapons; one called ‘Enfield’ and the other ‘Webley’ value of apostle teaspoons’.
The introduction of the ‘38 was much criticized at the time, since it was antique spanish candlesticks. held that the smaller bullet could not compare in stopping power with the old heavy lead ‘455 bullet space saving rectangular drop leaf tables. It is certainly a lighter revolver and easier to handle, but whether it permits any more accurate shooting in the hands of the trained shot is a moot point art deco burr walnut - antiques. The writer, in any case, could never make such good practice with it as he could with his old W epergne glass dish.G burr antique table. During the War, for a reason as yet unexplained, some Enfield ’38’s were made which could only fire double-action-, cocus wood oyster veneered. and were designated Mark I* rococo music. The only modification was the removal of the single-action bent “chinese screen” and “mother of pearl”.
A large number of American Smith and Wesson revolvers Of ‘38 calibre were made for the British Army during the Second World War brass frame girandole. As a ‘455 calibre weapon the Smith and Wesson had always been popular and had been purchased extensively as an officers’ private weapon 17th century tea tray. Instead of breaking open, the frame is solid and the cylinder swings out to the left louis xiv antique dining table designs. Ejection has to be carried out as a separate operation by pushing a rod attached to the front of the cylinder neoclassical sheraton style butlers sideboard.
